溜槽、輸送設備類
雙軸加濕攪拌機

SLW型雙管螺旋喂料器

DOUBLE-PIPE SCREW FEEDING ENGINE

 

該螺旋喂料機適用于干燥粉狀物料(如煤粉、水泥、谷物、砂石等)的均勻連續供料。

該設備采用擺線針輪減速機,加裝VF變頻器,調速范圍廣,運轉平穩、噪聲低、結構緊湊、體積小,可以方便地調節物料流量,滿足不同生產工藝要求。

The device is used to continually supply dry power material, such as coal power, cement, grain and sand etc.

The device is equipped with cycloid pin wheel speed reducer and VF transducer. It has the features of great range of timing, smooth operation, low noise, compact structure and small volume. It can adjust flow of material expediently and meet the demand of different production technics.

 

型號說明:

Model explanation:

              SLW-×××-××××

                                                                                                                                  

                                                 進出料口中心距 mm Center interval of inlet and outlet                                                     

                                       螺旋直徑mm Screw diameter

                                       規格代號 Spec code

 

雙管螺旋喂料機主要技術參數:

Main technical parameter:

規格型號

Type

轉速(r/min

Rotate   speed

輸送能力(m3/h

Transport   ability

計算需要功(kw)

Needed   power

減速器型號

Type   of reducer

重量kg

W

Φ125×1500

2080

25

0.491

BWD18-17-2.2

1160

Φ125×2500

2080

25

0.871

BWD18-17-2.2

1340

Φ150×1500

2679

510

0.987

BWD18-17-2.2

1550

Φ150×2500

2679

510

1.635

BWD22-17-4.0

1750

Φ175×1500

2580

616

1.57

BWD22-17-4.0

1750

Φ175×2500

2580

616

2.62

BWD22-17-4.0

1850

Φ200×1500

2580

825

2.45

BWD22-17-4.0

1820

Φ200×2500

2580

825

4.09

BWD22-17-5.5

1980

Φ250×2500

2065

1134

5.55

BWD22-17-7.5

2450

Φ300×3000

2065

2065

12.5

BWD33-17-15

3050

 

喂料能力計算:

Feeding ability calculation:

QQ圖片20150529140450.png

式中:

Q---雙管螺旋喂料機的喂料能力(m/h

Feeding   ability

D---螺旋葉直徑(m

Diameter   of screw leaf

d---螺旋桿直徑(m

Diameter   of screw pole

S---螺旋的螺距(m

Interval   of screw

 

δ---螺旋葉厚度(m

Thickness of   screw leaf

n---螺旋的轉速(r/min

Rotate speed of   screw

---物料的充滿系數(一般   =0.9

Filling   coefficient of material

 

SLW外形圖:

Appearance figure:

QQ圖片20150529140344.png

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SLW外形連接尺寸:

Appearance joint dimension:

規格

a×a1

b×b1

c×c1

n1-d1

A×A1

B×B1

C×C1

Φ125×1500

200×500

270×570

320×620

20-Ф13

500×500

570×570

620×620

Φ125×2500

200×500

270×570

320×620

20-Ф13

500×500

570×570

620×620

Φ150×1500

200×600

270×670

320×720

24-Ф13

600×600

670×670

720×720

Φ150×2500

200×600

270×670

320×720

24-Ф13

600×600

670×670

720×720

Φ175×1500

230×700

310×780

360×830

28-Ф13

700×700

780×780

830×830

Φ175×2500

230×700

310×780

360×830

28-Ф13

700×700

780×780

830×830

Φ200×1500

250×800

330×880

390×940

28-Ф13

800×800

880×880

940×940

Φ200×2500

250×800

330×880

390×940

28-Ф13

800×800

880×880

940×940

Φ250×2500

250×1000

330×1080

390×1140

36-Ф13

1000×1000

1080×1080

1140×1140

Φ300×3000

250×1200

330×1280

390×1340

44-Ф13

1200×1200

1280×1280

1340×1340

SLW外形連接尺寸:

Appearance joint dimension:

規格

n-d

n2-d2

H

H1

L

L0

L1

D

E

L2

E1

Φ125×1500

16-Ф18

16-Ф22

643

268

2000

2950

1500

250

620

1950

570

Φ125×2500

16-Ф18

32-Ф22

643

268

4000

4950

2500

250

620

3950

570

Φ150×1500

16-Ф18

26-Ф22

650

275

3000

3950

1500

300

720

2950

670

Φ150×2500

16-Ф18

34-Ф22

650

275

4000

4950

2500

300

720

3950

670

Φ175×1500

20-Ф18

28-Ф22

678

275

3200

4150

1500

350

830

3150

780

Φ175×2500

20-Ф18

36-Ф22

678

275

4200

5150

2500

350

830

4150

780

Φ200×1500

20-Ф18

30-Ф22

683

305

3430

4380

1500

400

940

3370

880

Φ200×2500

20-Ф18

36-Ф22

683

305

4430

5380

2500

400

940

4370

880

Φ250×2500

24-Ф23

42-Ф22

728

340

4850

5800

2500

570

1140

4790

1080

Φ300×3000

32-Ф23

48-Ф22

796

385

5550

6500

3000

620

1340

5490

1280

 

 

使用說明:

Usage explanation:

l         安裝時螺旋機各機殼及兩端機架的縱向不直度和水平度允差為長度的1/1000。底座在機殼裝妥以后使之著實,再擰緊地腳螺釘。

l         進出料口現場安裝,法蘭間連接加密封墊片,不得有間隙。

l         機體裝妥后應檢查各存油處是否有足夠潤滑油。

l         運行應平穩可靠,軸承箱不得發生漏油現象,軸承溫升不得超過20℃。

l         運行時加料應均勻,否則易造成輸送物料的積塞,驅動裝置過載。被輸送物料內不得混入堅硬的大塊物料,避免螺旋卡死造成機體損壞。

l         必需保證輸送機無負荷起動,在停車前應停止加料,待機殼內輸送完物料后,方能停止運轉。

l         使用中應經常檢查各機件的工作狀態,注意各傳動件是否運行良好,應經常加潤滑油。

l          The error of portrait linearity and horizontal of body and bracket is the 1/1000 of length when install screw engine. Install the support on the body steadily and then lock down the ground bolt.

l          Install the inlet and outlet on the spot. Add sealing shim between the two flanges and there is no clearance.

l          Check the oil store if there is enough lubricant after the installation is over.

l          The operation should be steady and reliable. There is no oil leakage in the bearing box and the raising temperature is not more than 20.

l          Feed the material equally, otherwise the material will be jammed and the driving device is over loaded. There is no big block hard material in the transported material to avoid blocking and damaging.

l          Make sure that the conveyer starts without load and stop feeding before stop the engine. Stop the conveyer after the material is transported completely.

l          Often check the working condition of all parts during the operating. Pay attention to the working of transmission parts and add lubricant to the transmission parts.

 

 

 

 

 

 

 


湖北澳星環保成套設備有限公司 版權所有

備案號: 鄂ICP備14001966號-1

地址:湖北省荊州市沙市區十號路98號 電話:0716-4302555 傳真:0716-4310988

香港经典a毛片免费观看hd